Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Tools

Park Tool Crown Race Cutting Tool
$545.99
To ensure proper headset performance and longevity, special attention must be given to accurately machine the fork’s crown race seat. Park Tool's Crown Race Cutting Tool is a professional-quality machining tool for milling both the outer edge and lower surfaces of the crown race seat. • Includes high speed steel cutters and adjustable collets to machine 26.5mm and 27.1mm crown race seats on 1” forks and 30.1mm crown race seats on 1-1/8" forks • Unique adjusting system allows a tight fit of the tool on any fork, threaded or unthreaded (even forks with externally butted steerer tubes), ensuring a smooth, accurate cut and proper alignment of the fork in the frame • Cutter sized for 1-inch standard is part #845 (sold separately) • Cutter for 1-1/8 inch standard is #846 (sold separately)
Park Tool Head Tube Reaming and Facing Set
$527.95
Proper frame preparation is very important. Park Tool's Head Tube Reaming and Facing Set combines reaming and facing of the head tube to create a perfect fit for most sizes of head cups. Includes: • 30.1 mm reamer (part #751.2) and four different size pilots (29.8mm, 30.0mm, 33.8mm, and 36.8mm) • 690 facer • Quick-release, quick-adjust feature: bottom portion slides off and on easily without threading SHIS terminology: The HTR-1 as stock will face frames of EC29, EC30, EC34 and EC37. It will ream frames of EC30. Accessories will allow service in other standards.
Park Tool Disc Brake Mount Facing Set
$465.95
The DT-5.2 is engineered and built to accurately face front or rear disc brake mounts so they are precisely aligned to the rotor. - Faces any IS Mount, Post Mount, or new Shimano Flat Mount, including low clearance, chainstay mounts - Telescoping axle adaptors allow use with any configuration of open or thru-axle dropouts and dropout widths (including Boost 110, Boost 148 and all fat bike axles) - Includes two facing cutters: IS Mounts Post and Flat Mounts - Includes storage case
Park Tool 49.59mm Head Tube Reamer & Facer for 1.5-Inch Headset Standard
$407.94
The Park Tool 758.2 will ream and face the head tubes of bike using the 1.5" standard. The 758.2 is designed for use with the Park Tool HTR-1 or HTR-1B Headtube Facer and Reamer. Must also be used with the 750.2 Centering Cone Adaptor.
Park Tool Trailhead Workstation
$399.95
A versatile repair center designed and built specially for the harsh conditions of the outdoors. The THS-1 can be bolted directly to an existing post, permanent structure or to the THP-1 Post (available separately). The weather-proof stand includes eight carefully chosen tools capable of helping with a wide variety of minor repairs and adjustments. The THS-1 also features an integrated, super stout cradle stand that gets both wheels off the ground making any job easier. A great addition to any trailhead, park, corporate campus, apartment building, school, bike shop or anywhere riders may need some help to get back on their bikes. Features: - All steel construction, plated then powder coated to withstand the elements - Tamper proof assembly fasteners - Includes eight tools specialty treated to increase durability outdoors and securely mounted on 1/8" galvanized, vinyl coated cable - 1.5-inch (3.8cm) tubular support arms, plated and powder coated, soft touch covers - Mounts to any post or flat surface (mounting fasteners not included) - Dimensions of tool box: 12.2 x 8.7 x 2.6-inch (31 x 22 x 6.6cm) - Tubes extend 17-inches (43cm) from mounting surface
Park Tool Bottom Bracket Facing Set
$385.95
Park Tool's Bottom Bracket Facing Set is designed to be a complete self-contained facing set, combining top-quality precision parts with ease of use. Simply install the threaded inserts using the facer handle, then insert the facing tool through the guides and install the tension spring and speed nut. After applying a liberal amount of cutting oil, the BFS-1 easily cuts the shell material, giving you a clean, faced surface. Now you're ready to install the bottom bracket. The English threading inserts are included. The Italian threading (36 x 24) inserts are available as an accessory, as part #688. Two are required.
Park Tool Right Hand Bottom Bracket Tap
$338.74
Park Tool's Right Hand Bottom Bracket Tap is a replacement tap for their BTS-1 Bottom Bracket Tap Set (sold separately). This tap is used on the non-drive or left side of the bike, which uses a clockwise or "right hand threading." Two taps are required for use.
Park Tool Reamer & Spacer Set for BB30 Bottom Bracket Shells
$327.88
Park Tool's 752 Reamer and Spacer Set allows reaming of bottom bracket frame shells in the BB30 standard. The reamer is sized at 41.94mm. It is used with the HTR-1 Head Tube Reamer and Facer and a 750.2 Centering Cone (each sold separately). The set includes a spacer to stop the reaming depth.
Park Tool Left-Hand Bottom Bracket Tap
$305.88
Park Tool's 692 Left-Hand Bottom Bracket Tap is a 1.370" x 24 TPI replacement tap for the BTS-1 Bottom Bracket Tap Set. This tap is used on the drive side (right side) of the bike. This side of the bottom bracket uses a counter-clockwise or left-hand thread. Note: It is very important to have sharp and accurate cutting tools for effective tapping and thread-chasing. Using an excessively worn or damaged tap can cause permanent damage to the frame and/or bottom bracket.
Park Tool Cutting Facer
$149.99 - $271.32
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.
Park Tool Reamer
$120.52 - $202.18
Park Tool offers premium-quality reamers for nearly any bicycle standard. The reamers below are designed to quickly, accurately, and precisely ream headtubes when used with Park's Head Tube Reamer (HTR), ensuring a perfect headset fit and prfoessional-quality bicycle build. Choose the correct reamer for your application using the following information: - 751.2: This reamer is sized to 30.1mm. This allows a 0.1mm interference fit when pressing the 30.2mm headset of the “Euro” one-inch standard. - 754.2: This reamer is sized to 33.9mm. The allows a 0.1mm interference fit when pressing the 34.0mm headset of the 1-1/8" standard. - 788: This reamer is sized to 43.95mm. It reams head tubes to accept “internal” headset cups with 44.05 - 44.10mm O.D. (1-1/8 ZS standard). It is used with Park Tool's 690-XL Facing Cutter and 750 Centering Cone. - 738: This reamer is sized to 52.1mm. It is used to ream head tubes using the 1-1/2" integrated headset standard. It is used with Park Tool's 690-XL Facing Cutter and 750.2 Centering Cone Adapter. - 789: This reamer is sized to 55.95mm. It is used to ream head tubes to accept “internal” headset cups with 56.00–56.10mm O.D. (1-1/2 ZS standard). It is used with Park Tool's 690-XXL Facing Cutter and #750 Centering Cone Adaptor. - 799: This reamer is sized to 47mm. It is used for cutting the lower head tube on frames using an IS47 bearing for a 1-1/4" integrated headset. It cuts a 45-degree bearing set shoulder.
Park Tool Adjustable Axle Set - For DT-5
$189.95
Upgrades the DT-5 to the DT-5.2. - Four telescoping axle adaptors - Two stand off studs for Flat Mount alignment - 12mm front fork thru axle sleeve
Park Tool BB86/92 Shell Reamer
$149.08
- Used to ream and face BB86/92 bottom bracket shells to an ID of 40.98mm - Used in conjunction with HTR-1 head tube reaming and facing set (PK-6710), 750.2 centering cone adapter (PK-6735) and 690-XL facing cutter (PK-6730)
Park Tool Ratcheting Click-Type Torque Wrench
$132.99
With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The TW-6.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). Designed for higher torque settings for repairs and installation in the bottom bracket, cassette lockring and other areas that use a higher torque settings. For lower torque setting, see the TW-5. Comes with its own protective case. - 10–60 Newton meter range (88–530 Inch Pounds) - Adjustable in 0.25 Nm increments - Ratcheting 3/8" drive - Reads and registers for both left hand and right hand threading - Dial-adjust system allows desired torque setting to be preset - Calibrated to be accurate to +/- 4% - Length: 36.2cm (14.25")
Park Tool WH-1 Wheel Holder
$109.99
No more need to hold wheels between your knees, balance on a bench top or ask for help. The WH-1 Wheel Holder firmly holds thru axle and quick release wheels at three convenient positions. It’s like having a strong helper to hold wheels during cleaning, tire and tube work, hub work, cassette work, and tubeless installation. The WH-1 can be bolted or clamped directly to a bench or installed in a bench vise. Uses and Features: - Quick and easy access to hold virtually any wheel to perfectly position your work for a variety of tasks including but not limited to: - Wheel building -Cassette removal and installation - Tire and tube removal and installation - Tubeless tire work - General cleaning - Hub work - Holds wheel at vertical, 35 degrees from vertical, and horizontal positions - Accepts 12, 15, and 20mm thru axles and 5mm skewers - E-Nickel finish for durability
Park Tool HBT-1 Hydraulic Barb Tool
$106.99
This handy tool will save time and frustration! Quickly and accurately cuts hydraulic brake line then precisely installs hose barbs into the tubing when the brake line is either on or off the bike. - Cuts hydraulic brake hose (does not cut steel braided hydraulic hose) - Installs press-in style barbed hose inserts - Replaceable parts including push pin tip and stainless steel blade - Hard anodized body for improved tool wear - Lightweight, CNC machined aluminum body Replacement parts: - 2494K Cutting Blade (set of 2) - 2497 Push Pin Tip
Park Tool Campagnolo Crank and Bearing Tool Set
$97.99
A complete tool set to work on both Campagnolo and Fulcrum Ultra-Torque and Power Torque crank and bottom bracket systems (each sold separately). The CBP-8 includes a beefed-up bearing and crank puller and all the fittings necessary to remove and install both systems. - Bearing Puller That Fits Both Power Torque And Ultra-Torque - Crank Puller For Power Torque - Bearing Setter For Both Power Torque And Ultra-Torque - Removal Adaptor For Power Torque Crank Bearings - Removal Protection Pads For Use With Carbon Cranks - Removal Protection Adaptor For Use With Aluminum Crank Arms - Crank Removal Extension Plug For Power Torque
Park Tool Crown Race Setting System — Oversized
$95.95
The CRS-15.2 uses two different insert rings to install bearing races on the 1.5-inch and 1-1/4-inch forks. The bearing surface is spared a direct hit by using aluminum inserts. Using a hammer, tap firmly on the end cap of the tube and seat the race into its proper place safely and accurately. Included extension allows work on fork steering tubes up to 425mm. - SHIS terminology: The CRS-15 services crown races in SHIS 33 and 40.
Park Tool Thru-Axle Tap
$29.95 - $86.95
Frame and Fork Taps will become a lifesaver at some time for virtually every mechanic. These taps are made of high-carbon steel and are precision ground. Park Tool Frame and Fork Taps cut easily and fit conventional tap handles.
Park Tool Spoke Tension Meter
$84.99
The key to wheels that are strong and reliable is having spokes that are properly and uniformly tensioned. Park's Spoke Tension Meter accurately and reliably measures the absolute tension of each of the spokes in a wheel, as well as the relative tension between all the spokes in a wheel. It's easy to use, affordable and it works on nearly any bicycle spoke, no matter its diameter, material or shape.
Park Tool Metric Wrench Set
$79.99
Never be left looking for an errant wrench when you have Park's Metric Wrench Set. It includes 12 high quality Park metric wrenches from 6 to 17mm in diameter, featuring both box and open ends. They are all forged from chrome vanadium steel, then chrome plated for durability and dipped in Park Tool blue vinyl for outstanding comfort and ease of use.
Park Tool Shop Cone Wrench Set
$79.99
Park Shop Cone Wrenches are made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on hubs and other bearing assemblies. Their special Y-heads put more material where it's needed for greater strength. Most applications require several cone wrenches, so Park gives you a whole set, featuring 13mm - 24mm, 26mm and 28mm wrenches to suit your repair needs.
Park Tool P-Handle Torx Compatible Wrench Set
$73.99
Engineered for fit, function, and leverage, these L-shaped shop-quality Torx compatible wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Torx compatible drivers at each end - Includes T6, T8, T10, T15, T20, T25, T30, and T40 - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization
Park Tool Adjustable Torque Driver
$72.99
Shop-quality, adjustable torque driver that limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The ATD-1.2 features all-metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at Park Tool's factory in Minnesota.
Park Tool Tool Kaddie with Stand Mount
$67.99
Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4 was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Stand Mount mounts to any Park Tool Professional Shop Stand (all versions of PRS-2, -3, -4, and -33) - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)
Park Tool Digital Caliper
$60.99
What's your seatpost size again? Park's Digital Caliper accurately measures seatposts, head tubes, bearings, spoke diameters, etc. It's a precision instrument built accurate to 0.01mm with a stainless-steel mechanisms and a rugged composite body. The tool’s ability to measure in metric, decimal inch, and fractional inch makes it an indispensable home workshop tool. It features an automatic shut-off and comes with a protective sleeve and the battery.
Park Tool Frame Alignment Gauge
$59.99
Many bicycles will not shift or track properly because the front and rear wheels are not in line with the frame. If these conditions still exist after wheel and derailleur adjustments, the seat stays, chain stays, and rear drop outs of the frame may be misaligned. For years the accepted method to check the alignment of the rear drop-out was to run a string on either side. This method does work to some extent. However, it is not accurate because the measurement is not taken at the drop-out. With the Park Tool Frame Alignment Gauge, the alignment can be checked quickly and accurately at the drop-out. It includes a retractable pointer to fit all sizes and types of bicycles.
Park Tool Sliding Thru Axle Adaptor
$59.99
The 1729-TA Sliding Thru Axle Adaptor is designed to allow any Park Tool PRS-20, PRS-21 or PRS-23 Repair Stand to accept 12mm and 15mm thru axle wheeled bikes.
Park Tool TSB-4 Tilting Truing Stand Base
$59.99
Securely holds the TS-4 Professional Wheel Truing Stand and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
Park Tool Tool Kaddie with Bench Mount
$59.95
Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4T was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Bench Top Mount sits firmly on any flat surface - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)
Page 1 of 8 Next page