Workstands

For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Portable Wheel Dishing Tool is a must. It disassembles quickly for storage or travel and allows you to easily check centering on road, mountain and BMX wheels from 24 to 29 inches in diameter and it works with any hub. The Wheel Alignment Gauge is a necessity for every wheelbuilder.

Keep your most-needed bike repair tools and supplies close at hand with Park's Work Tray. It easily installs on your Park PRS-15, PRS-10, or PRS-11 Repair Stand (sold separately). And it features 2 separate compartments, a lube holder, a tool/towel bar, a tab system that holds plastic grocery bags and 2 receiver pods for extra accessories.

Permanently and securely attach your Park Tool Repair Stand (sold separately) to the floor of your shop with Park's Floor Mounting Plate. Made with an 8" square of steel, it attaches to the stand with four bolts, which are included.

Park Tool's Repair Kit features the most common replacement parts for the 100-3C and 100-5C clamps. Includes: • 118s adjusting barrel • 117s eyebolt • 121s adjusting barrel pivot • 136 nut • 116s cap screws (2) • 108s-2 pins (2) • 107s-2 pin (1) • Washers (3) • E-clips (3)

A 6-inch (15cm) extension that easily mounts to the main beam of any PRS-22 or PRS-22.2 to accommodate longer wheelbase bikes with bottom bracket-to-front axle lengths over 28.75 inches, including CX, gravel and enduro style bikes.

Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)

The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Professional Race Stand. It makes travel easy and convenient, while also protecting your stand.

The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Team Race Stand. It makes travel easy and convenient, while also protecting your stand.

Park's Work Tray attaches easily to most of Park's repair stands (sold separately) to keep your tools and small parts close at hand. It has deep sides so your small items stay put and many slots for holding your tools. The Tool Tray fits Park's PRS-2, PRS-3, PRS-6, PRS-11, PRS-12, PCS-1 and PCS-4 repair stands.

Park Tool's 106-AC easily adapts the #106 Work Tray or PTH-1 Paper Towel Holder to fit 35mm-37mm upright tubes on PCS-9 Repair Stands, as well as 2003 and newer PCS-1, PCS-4, PCS-4-1, PCS-4-2 Repair Stands.

Park's Paper-Towel Holder is an accessory for Park's Professional Race Stand (sold separately). It attaches easily and holds a standard roll of paper towels. It also works great for hanging clothes, wheels and tires.